I was asked how I had wired up my gauges in my XR6 when I realised I couldn’t find anywhere that specifically showed you, so I thought I would do a write up on it! As I had done this quite a while ago, I can’t remember where I purchased my items from, but you can get them at most auto shops, or from online stores and ebay! You will need to purchase a mount for the gauges (You can get single, double and even triple mounts for the BA-BF falcons that go above the ICC) as well as the gauges to put in them. I purchased a double gauge holder, similar to the ones that were included in the FPV range.

I also purchased a vacuum/boost gauge (This was mainly the one I wanted) as well as a voltage gauge (This was originally purchased just as an easy to install substitute to fill the second pod, but has worked out well as I’m installing the carputer) What you purchase is up to you, but to install them is all going to be different, except for the wiring of the ground, power, ignition and illumination (which I’ll show you here) The easiest and least intrusive way I found to wire my gauges up was to connect them to the plug that lies behind the fuse box located in the cabin. It was originally intended to be used for bluetooth hands-free car kits, but as I have none, it was trivial to just use that. To do this though, you will need to purchase a 4 pin auto plug to connect your wiring to. I bought mine from Jaycar Electronics, cat code:. Como Actualizar El Software Del Motorola A1200 Manual. If you do however have a hands-free kit using it, you could splice into the wires, otherwise maybe find another source for your wiring. I also wired the illumination up to the traction control and fog light switch.

First things first, when working with anything electrical in the car, it’s always wise to disconnect the battery. Now to remove the top of the ICC, you’ll just need to stick a credit card at the back of it, and pry it upwards and out, it should just clip off as you pry it. Then, you’ll need to remove the ICC, which you can find instruction on. You might be able to do this without removing the ICC, and by just feeding the cables down, but I had no luck.

Now you’ll need to get the wiring that came with your gauges, and feed the cable down the drivers side behind the dash, until you can see them coming through the foot well. Then just pull them through until you have just enough wire above the ICC to plug the gauges in. Then you’ll need to wire up your plug.

What you’ll need to do is get the power, ground and ignition wire from each gauge, strip the wires, and twist them together (i. Phelps Laundry Card Hack Download Free. e. Twist the each of the power wires together, each of the gorund, etc.). Then using a lug crimper, crimp each one to their own male spade lug. Then, insert each lug into the respective spot shown in the diagram below (note, the bottom right is not used, it was originally intended to mute the audio for phone calls): Once you’ve done that, remove the fuse box cover that’s located to the right under the steering wheel. Now I removed the fuse box, to give you a better idea of what is behind it, but you can fairly easily connect it without removing it, and just by feeling it instead.

BA Falcon, installing vacuum gauge. Asking that i install it, so yeh. Have you got any photos so i can see what i. XR8 with a boost/vac gauge line running. A boost gauge can improve performance Those seeking to get the best performance out of their turbo or super charger vehicle can better regulate boost pressure with a. Download Usb Driver Windows Xp Sp1 Sp2 here.

There is only one plug that will fit behind there, so you can’t plug it into anything incorrectly. To remove the fuse box, disconnect the brown plug. Then unscrew each of the 3 bolts shown below. Then the remove each of the 5 plugs that are attached to the back of the fuse box, as well as unclipping the white OBDII connector. And finally, you can unclip the boot release as well. This is the socket we want to be plugging into, the blue one: Once you have connected your plug into the hands free socket behind the fuse box, then reattach the fuse box by just reversing the instructions. Next, you will need to connect the illumination wire.